ST-DAC-50G-QSFP-3
3-year warranty · Standard lead time 3–7 days
50G QSFP+ DAC — 3m, Built for Rack-to-Rack Links
The Sate Optics ST-DAC-50G-QSFP-3 is a 50G direct attach copper cable, factory-terminated with QSFP+ to QSFP+ connectors and cut to 3m(10ft) — sized for links between neighbouring racks.
Why This Module
- Lowest-cost way to link two ports: no transceivers, no fiber — one cable, and a passive DAC draws essentially no power
- 3m rack-to-rack reach: crosses to the neighbouring cabinet with room for overhead or underfloor routing
- Factory-terminated and plug-and-play: both ends arrive as one tested assembly — plug in, link up, with lower latency than an optical hop
Compatible with your platform — coded for major networking platforms, including Cisco, Juniper, Arista, Huawei, Nokia, H3C and ZTE; 100% tested before shipment.
Key Specifications
| Parameter | Specification |
| Connector Ends | QSFP+ to QSFP+ |
| Data Rate | 50Gbps |
| Cable Type | Passive twinax copper cable |
| Wire Gauge | 26AWG |
| Cable Length | 3m(10ft) |
| Signal Conditioning | None (passive) |
| Operating Temperature | 0~70℃ |
Used In
- QSFP+ switch and adapter ports on FDR InfiniBand and 50GbE fabrics
- HPC and storage nodes wired for low-latency cluster interconnect
- Rack-to-rack links between neighbouring cabinets
- Typical platforms: NVIDIA (Mellanox) ConnectX VPI adapters, InfiniBand FDR switch platforms and other 50G / 56G QSFP+ switches and NICs.
Not sure it fits your equipment? Request a Quote and tell us your switch model — we confirm compatibility before you order.
Where It Fits
- Rack-to-rack uplinks between neighbouring cabinets in the same row
- Middle-of-row aggregation over short copper runs
- Replacing transceiver pairs where the run is short enough for copper — lower cost, lower power, nothing to clean or pair
Every module is covered by a 3-year warranty with lifetime maintenance. Standard lead time is 3–7 days for most products, and samples are available for evaluation.
More in 56G QSFP+ DAC
| Part Number | Description | Picture | Data Rate(Mbps) | AWG | Media Type | Length | Temp.(℃) | Note | Datasheet |
|---|---|---|---|---|---|---|---|---|---|
| ST-DAC-50G-QSFP-1 | 50G QSFP+ to QSFP+ Passive DAC, 30AWG, 1m | ![]() |
50Gbps/50Gbps | 30AWG | Passive Direct Attach Copper Twinax Cable | 1m(3ft) | 0~70℃ | S50-PC01 Compatible; QSFP+ to QSFP+; <0.1W | |
| ST-DAC-50G-QSFP-2 | 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 2m | ![]() |
50Gbps/50Gbps | 26AWG | Passive Direct Attach Copper Twinax Cable | 2m(7ft) | 0~70℃ | S50-PC02 Compatible; QSFP+ to QSFP+; <0.1W | |
| ST-DAC-50G-QSFP-3 | 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 3m | ![]() |
50Gbps/50Gbps | 26AWG | Passive Direct Attach Copper Twinax Cable | 3m(10ft) | 0~70℃ | S50-PC03 Compatible; QSFP+ to QSFP+; <0.1W | |
| ST-DAC-56G-QSFP-1 | 50G QSFP+ to QSFP+ Passive DAC, 30AWG, 1m | ![]() |
56Gbps/56Gbps | 30AWG | Passive Direct Attach Copper Twinax Cable | 1m(3ft) | 0~70℃ | S56-PC01 Compatible; QSFP+ to QSFP+; <0.1W | |
| ST-DAC-56G-QSFP-2 | 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 2m | ![]() |
56Gbps/56Gbps | 26AWG | Passive Direct Attach Copper Twinax Cable | 2m(7ft) | 0~70℃ | S56-PC02 Compatible; QSFP+ to QSFP+; <0.1W | |
| ST-DAC-56G-QSFP-3 | 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 3m | ![]() |
56Gbps/56Gbps | 26AWG | Passive Direct Attach Copper Twinax Cable | 3m(10ft) | 0~70℃ | S56-PC03 Compatible; QSFP+ to QSFP+; <0.1W |


