• DAC cables

ST-DAC-56G-QSFP-1

ST-DAC-56G-QSFP-1
Email: sales@sateoptics.com

3-year warranty · Standard lead time 3–7 days

56G QSFP+ DAC — 1m, Built for In-Rack Links

The Sate Optics ST-DAC-56G-QSFP-1 is a 56G direct attach copper cable, factory-terminated with QSFP+ to QSFP+ connectors and cut to 1m(3ft) — sized for links inside one rack.

Why This Module

  • Lowest-cost way to link two ports: no transceivers, no fiber — one cable, and a passive DAC draws essentially no power
  • 1m in-rack reach: spans stacked switches and the servers in the same cabinet, with slack to route neatly
  • Factory-terminated and plug-and-play: both ends arrive as one tested assembly — plug in, link up, with lower latency than an optical hop
  • Compatible with your platform — coded for major networking platforms, including Cisco, Juniper, Arista, Huawei, Nokia, H3C and ZTE; 100% tested before shipment.

Key Specifications

ParameterSpecification
Connector EndsQSFP+ to QSFP+
Data Rate56Gbps
Cable TypePassive twinax copper cable
Wire Gauge30AWG
Cable Length1m(3ft)
Signal ConditioningNone (passive)
Operating Temperature0~70℃

Used In

  • QSFP+ switch and adapter ports on FDR InfiniBand and 50GbE fabrics
  • HPC and storage nodes wired for low-latency cluster interconnect
  • In-rack links within a single cabinet
  • Typical platforms: NVIDIA (Mellanox) ConnectX VPI adapters, InfiniBand FDR switch platforms and other 50G / 56G QSFP+ switches and NICs.

Not sure it fits your equipment? Request a Quote and tell us your switch model — we confirm compatibility before you order.

Where It Fits

  • Top-of-rack switching with servers cabled straight into the switch above them
  • Stacked and clustered switches patched inside one cabinet
  • Replacing transceiver pairs where the run is short enough for copper — lower cost, lower power, nothing to clean or pair

Every module is covered by a 3-year warranty with lifetime maintenance. Standard lead time is 3–7 days for most products, and samples are available for evaluation.

More in 56G QSFP+ DAC

Part Number Description Picture Data Rate(Mbps) AWG Media Type Length Temp.(℃) Note Datasheet
ST-DAC-50G-QSFP-1 50G QSFP+ to QSFP+ Passive DAC, 30AWG, 1m ST-DAC-50G-QSFP-1 50Gbps/50Gbps 30AWG Passive Direct Attach Copper Twinax Cable 1m(3ft) 0~70℃ S50-PC01 Compatible; QSFP+ to QSFP+; <0.1W
ST-DAC-50G-QSFP-2 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 2m ST-DAC-50G-QSFP-2 50Gbps/50Gbps 26AWG Passive Direct Attach Copper Twinax Cable 2m(7ft) 0~70℃ S50-PC02 Compatible; QSFP+ to QSFP+; <0.1W
ST-DAC-50G-QSFP-3 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 3m ST-DAC-50G-QSFP-3 50Gbps/50Gbps 26AWG Passive Direct Attach Copper Twinax Cable 3m(10ft) 0~70℃ S50-PC03 Compatible; QSFP+ to QSFP+; <0.1W
ST-DAC-56G-QSFP-1 50G QSFP+ to QSFP+ Passive DAC, 30AWG, 1m ST-DAC-56G-QSFP-1 56Gbps/56Gbps 30AWG Passive Direct Attach Copper Twinax Cable 1m(3ft) 0~70℃ S56-PC01 Compatible; QSFP+ to QSFP+; <0.1W
ST-DAC-56G-QSFP-2 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 2m ST-DAC-56G-QSFP-2 56Gbps/56Gbps 26AWG Passive Direct Attach Copper Twinax Cable 2m(7ft) 0~70℃ S56-PC02 Compatible; QSFP+ to QSFP+; <0.1W
ST-DAC-56G-QSFP-3 50G QSFP+ to QSFP+ Passive DAC, 26AWG, 3m ST-DAC-56G-QSFP-3 56Gbps/56Gbps 26AWG Passive Direct Attach Copper Twinax Cable 3m(10ft) 0~70℃ S56-PC03 Compatible; QSFP+ to QSFP+; <0.1W