ST-DAC-QSFPDD-8*SFP56-1
3-year warranty · Standard lead time 3–7 days
QSFP-DD to 8× SFP56 Breakout DAC — 1m, Built for In-Rack Links
The Sate Optics ST-DAC-QSFPDD-8*SFP56-1 is a 400G to 8× 50G breakout direct attach copper cable, factory-terminated with QSFP-DD to 8× SFP56 connectors and cut to 1m(3ft) — sized for links inside one rack.
Why This Module
- One port, 8 links: a single 400G switch port fans out to 8× 50G — dense breakout wiring without separate transceivers
- 1m in-rack reach: spans stacked switches and the servers in the same cabinet, with slack to route neatly
- Factory-terminated and plug-and-play: both ends arrive as one tested assembly — plug in, link up, with lower latency than an optical hop
Compatible with your platform — coded for major networking platforms, including Cisco, Juniper, Arista, Huawei, Nokia, H3C and ZTE; 100% tested before shipment.
Key Specifications
| Parameter | Specification |
| Connector Ends | QSFP-DD to 8× SFP56 |
| Data Rate | 400Gbps to 8× 50Gbps |
| Cable Type | Passive twinax copper breakout cable |
| Wire Gauge | 30AWG |
| Cable Length | 1m(3ft) |
| Signal Conditioning | None (passive) |
| Operating Temperature | 0~70℃ |
Used In
- One 400G port split into 8× 50G links
- QSFP-DD spine-to-leaf fan-out wiring
- In-rack links within a single cabinet
- Typical platforms: Cisco Nexus 9300 series, Arista 7060X / 7388 series, Juniper QFX5220 / QFX5700, Huawei CloudEngine 16800, Nokia 7250 IXR, H3C S12500 / S9820 series.
Not sure it fits your equipment? Request a Quote and tell us your switch model — we confirm compatibility before you order.
Where It Fits
- Top-of-rack switching with servers cabled straight into the switch above them
- Stacked and clustered switches patched inside one cabinet
- Replacing transceiver pairs where the run is short enough for copper — lower cost, lower power, nothing to clean or pair
Every module is covered by a 3-year warranty with lifetime maintenance. Standard lead time is 3–7 days for most products, and samples are available for evaluation.
More in 400G QSFP-DD To 8x50G SFP56 Breakout DAC
| Part Number | Description | Picture | Data Rate(Mbps) | AWG | Media Type | Length | Temp.(℃) | Note | Datasheet |
|---|---|---|---|---|---|---|---|---|---|
| ST-DAC-QSFPDD-8*SFP56-0.5 | 400G QSFP-DD to 8x50G SFP56 Passive DAC, 30AWG, 0.5m | ![]() |
400Gbps/8x50Gbps | 30AWG | Passive Direct Attach Copper Breakout Cable | 0.5m(2ft) | 0~70℃ | CAB-D-8S-400G-0.5M Compatible; QSFP-DD to 8x50G SFP56; <0.1W | |
| ST-DAC-QSFPDD-8*SFP56-1 | 400G QSFP-DD to 8x50G SFP56 Passive DAC, 30AWG, 1m | ![]() |
400Gbps/8x50Gbps | 30AWG | Passive Direct Attach Copper Breakout Cable | 1m(3ft) | 0~70℃ | CAB-D-8S-400G-1M Compatible; QSFP-DD to 8x50G SFP56; <0.1W | |
| ST-DAC-QSFPDD-8*SFP56-1.5 | 400G QSFP-DD to 8x50G SFP56 Passive DAC, 30AWG, 1.5m | ![]() |
400Gbps/8x50Gbps | 30AWG | Passive Direct Attach Copper Breakout Cable | 1.5m(5ft) | 0~70℃ | CAB-D-8S-400G-1.5M Compatible; QSFP-DD to 8x50G SFP56; <0.1W | |
| ST-DAC-QSFPDD-8*SFP56-2 | 400G QSFP-DD to 8x50G SFP56 Passive DAC, 28AWG, 2m | ![]() |
400Gbps/8x50Gbps | 28AWG | Passive Direct Attach Copper Breakout Cable | 2m(7ft) | 0~70℃ | CAB-D-8S-400G-2M Compatible; QSFP-DD to 8x50G SFP56; <0.1W | |
| ST-DAC-QSFPDD-8*SFP56-2.5 | 400G QSFP-DD to 8x50G SFP56 Passive DAC, 28AWG, 2.5m | ![]() |
400Gbps/8x50Gbps | 28AWG | Passive Direct Attach Copper Breakout Cable | 2.5m(8ft) | 0~70℃ | CAB-D-8S-400G-2.5M Compatible; QSFP-DD to 8x50G SFP56; <0.1W | |
| ST-DAC-QSFPDD-8*SFP56-3 | 400G QSFP-DD to 8x50G SFP56 Passive DAC, 28AWG, 3m | ![]() |
400Gbps/8x50Gbps | 28AWG | Passive Direct Attach Copper Breakout Cable | 3m(10ft) | 0~70℃ | CAB-D-8S-400G-3M Compatible; QSFP-DD to 8x50G SFP56; <0.1W |


